Fusion Engineering and Design

An International Journal for Fusion Energy and Technology devoted to Experiments, Theory, Methods and Design

公式サイト

Impact Factor

1.7

Citescore

3.7

最新論文

Corrigendum to “Improving the Newton cooling model to drive the optimization method for heterogeneous storage of ECRH hot data” [Fusion Engineering and Design 215 (2026) 115715]
Corrigendum to “Relativistic effects on stopping power of plasmas with heavy ions” [Fusion Engineering and Design 205 (2024), 114524]
Corrigendum to “Initial accident scenario analysis in support of a preliminary DEMO tritium plant design” [Fusion Engineering and Design 189 (2023) 113482]
Thermal behaviour of ZrCo getter beds during hydrogen absorption at variable flow rates and concentrations
Performance of the W7-X ECRH gyrotron diamond output window at 2 MW operation

AI解説分析論文一覧

Fusion Engineering and Design

最新論文

Fusion Engineering and Design

最新論文

Investigation of the correlation between the electrical contact resistance and the contact area of mechanical lap joint fabricated with high-temperature superconducting tapes using X-ray microtomography

Assessment of electromagnetic loads for EAST plasma facing components using integral parameters method

Upgrade of poloidal field coils current measurement system on Experimental Advanced Superconducting Tokamak

The data acquisition and control system for the operation of ASDEX pressure gauge for the measurement of neutral pressure in ADITYA Tokamak

Assessment of n = 1 “overlap” error field produced by localized steel objects placed at different levels of ITER Tokamak building

Effects of activation products on tritium measurements for tungsten in fusion reactors

Preliminary results of CuCrZr/316L tube-to-tube junctions fabricated with rotary friction welding

Automated mode recovery for gyrotrons demonstrated at Wendelstein 7-X

Effects of structural and concentration polarization on the efficiency of Pd membrane permeator

Leak tight joint procedures for ODS-Cu/ODS-Cu by the advanced brazing technique

Design of tomographic diagnostic system for Indian Test Facility (INTF) neutral beam injector

Corrigendum to “Development of the material property handbook and database of CuCrZr” [Fusion Eng. Des. 144 (July) (2019) 148–153]

Welding technology development for the fabrication of vacuum vessel for CFETR

Conceptual design of a high heat flux testing facility in support of CFETR

First plasma scenario development for HL-2M

Optimization of W/Cu monoblock mock-up with FGM interlayer for CFETR devertor targets

Systems engineering activities supporting the heating & current drive and fuelling lines systems integration in the European DEMO breeding blanket

Tokamak-agnostic actuator management for multi-task integrated control with application to TCV and ITER

Development of a 1D thermofluid code for divertor target plate modeling

Challenges and status of the ITER IVC conductor qualification process in China

Phase transformations in reduced-activation duplex alloy Fe52Mn30Cr18 under isothermal heat treatment

A DEM-CFD numerical model for the prediction of the effective thermal conductivity of pebble beds with contact conduction

A large field of view visible cameras image acquisition and processing technology in EAST device

Application of ADVANTG to the JET3 – NEXP streaming benchmark experiment

Design and analysis of thermal hydraulic performance of compact heat exchanger for FDS-II auxiliary system

Design of a PAM launcher and comparative analysis with the old FAM launcher for 2.45 GHz LHCD system on EAST

Design and analysis of a high power supply for the research system of superconducting magnets

Numerical simulation on residual stress eliminated by shot peening using SPH method

Multiphysics analysis of the Passive Active Multijunction (PAM) launcher for LHCD system of ADITYA-Upgrade tokamak

The novel short circuit withstand test configuration for ITER VS1 power transformer

Fusion Engineering and Design

最新論文

Fusion Engineering and Design

最新論文

Investigation of the correlation between the electrical contact resistance and the contact area of mechanical lap joint fabricated with high-temperature superconducting tapes using X-ray microtomography

Assessment of electromagnetic loads for EAST plasma facing components using integral parameters method

Upgrade of poloidal field coils current measurement system on Experimental Advanced Superconducting Tokamak

The data acquisition and control system for the operation of ASDEX pressure gauge for the measurement of neutral pressure in ADITYA Tokamak

Assessment of n = 1 “overlap” error field produced by localized steel objects placed at different levels of ITER Tokamak building

Effects of activation products on tritium measurements for tungsten in fusion reactors

Preliminary results of CuCrZr/316L tube-to-tube junctions fabricated with rotary friction welding

Automated mode recovery for gyrotrons demonstrated at Wendelstein 7-X

Effects of structural and concentration polarization on the efficiency of Pd membrane permeator

Leak tight joint procedures for ODS-Cu/ODS-Cu by the advanced brazing technique

Design of tomographic diagnostic system for Indian Test Facility (INTF) neutral beam injector

Corrigendum to “Development of the material property handbook and database of CuCrZr” [Fusion Eng. Des. 144 (July) (2019) 148–153]

Welding technology development for the fabrication of vacuum vessel for CFETR

Conceptual design of a high heat flux testing facility in support of CFETR

First plasma scenario development for HL-2M

Optimization of W/Cu monoblock mock-up with FGM interlayer for CFETR devertor targets

Systems engineering activities supporting the heating & current drive and fuelling lines systems integration in the European DEMO breeding blanket

Tokamak-agnostic actuator management for multi-task integrated control with application to TCV and ITER

Development of a 1D thermofluid code for divertor target plate modeling

Challenges and status of the ITER IVC conductor qualification process in China

Phase transformations in reduced-activation duplex alloy Fe52Mn30Cr18 under isothermal heat treatment

A DEM-CFD numerical model for the prediction of the effective thermal conductivity of pebble beds with contact conduction

A large field of view visible cameras image acquisition and processing technology in EAST device

Application of ADVANTG to the JET3 – NEXP streaming benchmark experiment

Design and analysis of thermal hydraulic performance of compact heat exchanger for FDS-II auxiliary system

Design of a PAM launcher and comparative analysis with the old FAM launcher for 2.45 GHz LHCD system on EAST

Design and analysis of a high power supply for the research system of superconducting magnets

Numerical simulation on residual stress eliminated by shot peening using SPH method

Multiphysics analysis of the Passive Active Multijunction (PAM) launcher for LHCD system of ADITYA-Upgrade tokamak

The novel short circuit withstand test configuration for ITER VS1 power transformer

Assessment of n = 1 “overlap” error field produced by localized steel objects placed at different levels of ITER Tokamak building