Fusion Engineering and Design

An International Journal for Fusion Energy and Technology devoted to Experiments, Theory, Methods and Design

公式サイト

Impact Factor

1.7

Citescore

3.7

最新論文

Corrigendum to “Improving the Newton cooling model to drive the optimization method for heterogeneous storage of ECRH hot data” [Fusion Engineering and Design 215 (2026) 115715]
Corrigendum to “Relativistic effects on stopping power of plasmas with heavy ions” [Fusion Engineering and Design 205 (2024), 114524]
Corrigendum to “Initial accident scenario analysis in support of a preliminary DEMO tritium plant design” [Fusion Engineering and Design 189 (2023) 113482]
Thermal behaviour of ZrCo getter beds during hydrogen absorption at variable flow rates and concentrations
Performance of the W7-X ECRH gyrotron diamond output window at 2 MW operation

AI解説分析論文一覧

Fusion Engineering and Design

最新論文

Fusion Engineering and Design

最新論文

Effect of annealing on the microstructure behavior of D+-irradiated W-2vol.%TiC composite prepared by wet-chemical method

On the feasibility of fusion–fission hybrid based on deuterium fuelled tokamak

The numerical analysis on the variation of electric potential, electric current and Lorentz force with its influence on buoyancy-driven conjugate heat transfer and fluid flow using OpenFOAM

Physical design of the neutralizer for CFETR negative ion based neutral beam injection prototype

Shielding proposal to mitigate the PFC #2 heating due to 16N decay photon radiation from the activated cooling water

Thermal hydraulic design and analysis of updated CFETR water cooled ceramic breeder blanket

Design, installation and operation of in-vessel resonant magnetic perturbation system on the HL-2A tokamak

X-ray imaging diagnostic in the high heat flux test facilities

The properties of the tungsten coating on fine grain graphite using pulsed laser deposition

The generation of sub-millimeter lithium granules from liquid Jet for magnetic fusion applications

Development of the internal matrix reinforcement bronze processed Nb3Sn multicore wires using Cu-Sn-In ternary alloy matrix for fusion magnet application

Study on microstructure change and hardening of 316L steel weld seam after helium ion irradiation

Preliminary assessment of vertical instability with blanket in CFETR

Analysis of the fracture mechanism at cryogenic temperatures of thick 316LN laser welded joints

Proposal of optimized power cycles for the DEMO power plant (EUROfusion)

Magnet coil power supply by a self-excited induction generator with a flywheel for a small tokamak, PHiX

Liquid tin interactions with ISTTOK plasmas

Designing of cooling water system for a pyro-breaker utilized in superconductive fusion facility

Ion source backplate loading due to backstreaming electrons and the arc discharge in the JET EP2 neutral beam injectors

Study of flow instability in parallel channel system for water cooled blanket

Optimum preparation of Fe-Al/α-Al2O3 coating on 21-6-9 austenitic stainless steel

First-principles study of the diffusion of Li in bcc Fe

Effects of gaseous media on interfacial microstructure and mechanical properties of titanium/steel explosive welded composite plate

Effect of simulated stress-relieving heat treatment on microstructure and tensile properties of CLAM steel

Geometrical effect in the measurement of the CXRS on EAST

Development of the quasi-optical combiner systems for density profile reflectometers on the EAST tokamak

Effect of welding techniques on the microstructure and mechanical properties of reduced activation ferritic-martensitic (RAFM) steel weld joints

Measurement of n = 1 locked mode using locked mode coils in KSTAR

Low energy deuterium plasma driven permeation through tungsten

Calibration of the gamma-ray measurement procedure in the EAST neutron activation system

Fusion Engineering and Design

最新論文

Fusion Engineering and Design

最新論文

Effect of annealing on the microstructure behavior of D+-irradiated W-2vol.%TiC composite prepared by wet-chemical method

On the feasibility of fusion–fission hybrid based on deuterium fuelled tokamak

The numerical analysis on the variation of electric potential, electric current and Lorentz force with its influence on buoyancy-driven conjugate heat transfer and fluid flow using OpenFOAM

Physical design of the neutralizer for CFETR negative ion based neutral beam injection prototype

Shielding proposal to mitigate the PFC #2 heating due to 16N decay photon radiation from the activated cooling water

Thermal hydraulic design and analysis of updated CFETR water cooled ceramic breeder blanket

Design, installation and operation of in-vessel resonant magnetic perturbation system on the HL-2A tokamak

X-ray imaging diagnostic in the high heat flux test facilities

The properties of the tungsten coating on fine grain graphite using pulsed laser deposition

The generation of sub-millimeter lithium granules from liquid Jet for magnetic fusion applications

Development of the internal matrix reinforcement bronze processed Nb3Sn multicore wires using Cu-Sn-In ternary alloy matrix for fusion magnet application

Study on microstructure change and hardening of 316L steel weld seam after helium ion irradiation

Preliminary assessment of vertical instability with blanket in CFETR

Analysis of the fracture mechanism at cryogenic temperatures of thick 316LN laser welded joints

Proposal of optimized power cycles for the DEMO power plant (EUROfusion)

Magnet coil power supply by a self-excited induction generator with a flywheel for a small tokamak, PHiX

Liquid tin interactions with ISTTOK plasmas

Designing of cooling water system for a pyro-breaker utilized in superconductive fusion facility

Ion source backplate loading due to backstreaming electrons and the arc discharge in the JET EP2 neutral beam injectors

Study of flow instability in parallel channel system for water cooled blanket

Optimum preparation of Fe-Al/α-Al2O3 coating on 21-6-9 austenitic stainless steel

First-principles study of the diffusion of Li in bcc Fe

Effects of gaseous media on interfacial microstructure and mechanical properties of titanium/steel explosive welded composite plate

Effect of simulated stress-relieving heat treatment on microstructure and tensile properties of CLAM steel

Geometrical effect in the measurement of the CXRS on EAST

Development of the quasi-optical combiner systems for density profile reflectometers on the EAST tokamak

Effect of welding techniques on the microstructure and mechanical properties of reduced activation ferritic-martensitic (RAFM) steel weld joints

Measurement of n = 1 locked mode using locked mode coils in KSTAR

Low energy deuterium plasma driven permeation through tungsten

Calibration of the gamma-ray measurement procedure in the EAST neutron activation system

Measurement of n = 1 locked mode using locked mode coils in KSTAR